Back to Top

1
Hi, Guest!
  • FISHER XLT-30A Acoustical leak detector

FISHER XLT-30A Acoustical Leak Detector

Update Terakhir
:
01 / 12 / 2019
Min. Pembelian
:
1 Unit

Harga

CALL
PT. Daya Teknik Meterindo
Harco Glodok Lantai 5 Blok F7
Office: Jl. Hayam Wuruk No. 2-5 Jakarta Barat, DKI Jakarta, 11180
Phone: (021) 2268-7062
HP: 0813-1516-6062; 0812-8222-5340; 0821-2214-8707
Email: [email protected]
Up. Irwan Pangaribuan

Detail FISHER XLT-30A Acoustical Leak Detector

FISHER XLT-30A Acoustical leak detector Version A: With the Big Foot Probe Also known as the Ground Microphone, this sensor is to be used on hard surfaces, concrete, asphalt, tile, etc. A fl exible rubber shield helps pre- vent outside sounds from interfering with the sounds from the buried pipe. Press and hold the red button near the handle to mute the audio from the probe and suppress loud sounds when the probe is moved. Kit also includes: 1. Hydrophonic Cylinder Probe This probe is a direct contact probe designed to make direct connection to the pipe, or any portion of the pipe that is accessible. Used in any combination of Sound Rods with the T-Handle, pipes can be accessed to distances up to nearly 6 feet away. Another feature of the Cylinder Probe is the ability to listen to pipe noise in pipes that are buried in turf, or soft surfaces. Accurate pipe location is essential for the placement of the Ground Rods as close to the pipe as possible. On top of the Cylinder Probe is a three position toggle switch for mute, listen, and momentary listen. As with all mute controls, learn to use them wisely. When tightening the sounds rods to the Hydrophonic Probe, secure the connector with a wrench as to not let it twist. Twisting of that connector could damage wiring on the inside of the probe. 2. Sound Rods Two different sizes are included with the XLT-30. Rods give the user various lengths for direct or indirect contact to pipes. 3. T-Handle This handle is used primarily with the Cylinder Probe and the sound rods. 4. Headphones These headphones are designed to deliver the clearest sound with the least distortion. The Volume knob can be used to adjust the audio level. Unplugging the headphones will turn off the XLT-30. When the XLT-30 is turned off, any modifications to the Volume, Notch, and Filter will return to the factory presets. 5. Probe Cable This cable attaches at the back of the Control Housing to any of the various probes. Make sure the jack is fully inserted and the lock nut is hand tightened. 6. Carrying Strap/ Housing Mounting Bracket The attachment system for the XLT-30 consists of a plastic mounting bracket that slides f rom the bottom of the control housing up to the bezel around the faceplate. There are two slots for attaching an adjustable strap that hangs around the neck of the user. Specification Operating Frequency : 60 Hz – 6 kHz, Gain = 95 db 20 Hz – 60 Hz, Gain > 90 dB Filter Types and Frequency Ranges : All Pass: 60 Hz to 6 kHz Low Pass : Adjustable cut-off frequency from 150 Hz to 2.4 kHz High Pass : Adjustable pass band frequency from 150 Hz to 2.4 kHz Band Pass : Adjustable center frequency from 150 Hz to 2.4 kHz Notch Filter : Adjustable center frequency rejection from 150 Hz to 2.4 kHz Can be used simultaneously with any filter option Output Indications: Audio : High performance headphones ( 64 ohms) Visual : LCD bar graph and 2-digit numeric display Grade of Protection : Splash Proof Battery Test : Automatic Battery Quantity/ Type : 2 / 9V Alkaline Battery Life : 50 Hours ( approximately) Shipping Weight : 20 Power Supply : Two 9V Batteries Manufacturer : Fisher M-Scope MPN : XLT-30A Manufacturer Warranty : 2 Years
Tampilkan Lebih Banyak
Kontak Kami